Safe - Compile and execute code in restricted compartments |
Safe - Compile and execute code in restricted compartments
use Safe;
$compartment = new Safe;
$compartment->permit(qw(time sort :browse));
$result = $compartment->reval($unsafe_code);
The Safe extension module allows the creation of compartments in which perl code can be evaluated. Each compartment has
Code which is compiled outside the compartment can choose to place variables into (or share variables with) the compartment's namespace and only that data will be visible to code evaluated in the compartment.
By default, the only variables shared with compartments are the ``underscore'' variables $_ and @_ (and, technically, the less frequently used %_, the _ filehandle and so on). This is because otherwise perl operators which default to $_ will not work and neither will the assignment of arguments to @_ on subroutine entry.
The default operator mask for a newly created compartment is the ':default' optag.
It is important that you read the Opcode(3)
module documentation
for more information, especially for detailed definitions of opnames,
optags and opsets.
Since it is only at the compilation stage that the operator mask applies, controlled access to potentially unsafe operations can be achieved by having a handle to a wrapper subroutine (written outside the compartment) placed into the compartment. For example,
$cpt = new Safe; sub wrapper { # vet arguments and perform potentially unsafe operations } $cpt->share('&wrapper');
The authors make no warranty, implied or otherwise, about the suitability of this software for safety or security purposes.
The authors shall not in any case be liable for special, incidental, consequential, indirect or other similar damages arising from the use of this software.
Your mileage will vary. If in any doubt do not use it.
The interface to the Safe module has changed quite dramatically since version 1 (as supplied with Perl5.002). Study these pages carefully if you have code written to use Safe version 1 because you will need to makes changes.
To create a new compartment, use
$cpt = new Safe;
Optional argument is (NAMESPACE), where NAMESPACE is the root namespace to use for the compartment (defaults to ``Safe::Root0'', incremented for each new compartment).
Note that version 1.00 of the Safe module supported a second optional parameter, MASK. That functionality has been withdrawn pending deeper consideration. Use the permit and deny methods described below.
The following methods can then be used on the compartment object returned by the above constructor. The object argument is implicit in each case.
variable(s)
in the argument list with the compartment.
This is almost identical to exporting variables using the the Exporter manpage
module.
Each NAME must be the name of a variable, typically with the leading type identifier included. A bareword is treated as a function name.
Examples of legal names are '$foo' for a scalar, '@foo' for an array, '%foo' for a hash, '&foo' or 'foo' for a subroutine and '*foo' for a glob (i.e. all symbol table entries associated with ``foo'', including scalar, array, hash, sub and filehandle).
Each NAME is assumed to be in the calling package. See share_from for an alternative method (which share uses).
share()
but allows you to explicitly name the
package that symbols should be shared from. The symbol names (including
type characters) are supplied as an array reference.
$safe->share_from('main', [ '$foo', '%bar', 'func' ]);
$cpt = new Safe 'Root'; $Root::foo = "Hello world"; # Equivalent version which doesn't need to know $cpt's package name: ${$cpt->varglob('foo')} = "Hello world";
The code can only see the compartment's namespace (as returned by the
root method). The compartment's root package appears to be the
main::
package to the code inside the compartment.
Any attempt by the code in STRING to use an operator which is not permitted by the compartment will cause an error (at run-time of the main program but at compile-time for the code in STRING). The error is of the form ``%s trapped by operation mask operation...''.
If an operation is trapped in this way, then the code in STRING will not be executed. If such a trapped operation occurs or any other compile-time or return error, then $@ is set to the error message, just as with an eval().
If there is no error, then the method returns the value of the last expression evaluated, or a return statement may be used, just as with subroutines and eval(). The context (list or scalar) is determined by the caller as usual.
This behaviour differs from the beta distribution of the Safe extension
where earlier versions of perl made it hard to mimic the return
behaviour of the eval()
command and the context was always scalar.
Some points to note:
If the entereval op is permitted then the code can use eval ``...'' to 'hide' code which might use denied ops. This is not a major problem since when the code tries to execute the eval it will fail because the opmask is still in effect. However this technique would allow clever, and possibly harmful, code to 'probe' the boundaries of what is possible.
Any string eval which is executed by code executing in a compartment, or by code called from code executing in a compartment, will be eval'd in the namespace of the compartment. This is potentially a serious problem.
Consider a function foo()
in package pkg compiled outside a compartment
but shared with it. Assume the compartment has a root package called
'Root'. If foo()
contains an eval statement like eval '$foo = 1' then,
normally, $pkg::foo will be set to 1. If foo()
is called from the
compartment (by whatever means) then instead of setting $pkg::foo, the
eval will actually set $Root::pkg::foo.
This can easily be demonstrated by using a module, such as the Socket module, which uses eval ``...'' as part of an AUTOLOAD function. You can 'use' the module outside the compartment and share an (autoloaded) function with the compartment. If an autoload is triggered by code in the compartment, or by any code anywhere that is called by any means from the compartment, then the eval in the Socket module's AUTOLOAD function happens in the namespace of the compartment. Any variables created or used by the eval'd code are now under the control of the code in the compartment.
A similar effect applies to all runtime symbol lookups in code called from a compartment but not compiled within it.
Note that this behaviour differs from version 1.00 of the Safe module where the root module could be used to change the namespace. That functionality has been withdrawn pending deeper consideration.
With no MASK argument present, it returns the current operator mask of the compartment.
With the MASK argument present, it sets the operator mask for the compartment (equivalent to calling the deny_only method).
This section is currently just an outline of some of the things code in a compartment might do (intentionally or unintentionally) which can have an effect outside the compartment.
Setting up a signal handler will need to be carefully considered and controlled. What mask is in effect when a signal handler gets called? If a user can get an imported function to get an exception and call the user's signal handler, does that user's restricted mask get re-instated before the handler is called? Does an imported handler get called with its original mask or the user's one?
Originally designed and implemented by Malcolm Beattie, mbeattie@sable.ox.ac.uk.
Reworked to use the Opcode module and other changes added by Tim Bunce <Tim.Bunce@ig.co.uk>.
Safe - Compile and execute code in restricted compartments |